REMOTE GUIDE
Multi-Channel
Specifications
Pairing Motors to Channels
1. Select Channel using (Left/Right) Buttons
2. Hold motor button for two seconds - motor jogs up and down
3. Hold Stop Button on remote for 3 seconds - motor jogs up and down. The motor is now
To unpair the remote from the motor, repeat the steps above.
To pair a back-up remote to the motor, press the (P) button 2 times on Remote A (already paired
Direction Reversing
Can be done by holding the motor button for three jog cycles (this works even if limits have been set)
If limits haven’t been set, you can hold the Favorite Button and the Stop Button for 2 seconds.
Limit setting
Your shade(s) should have limits set when they arrive at your facility. If for any reason your limits
are not set, follow the quick and easy instructions below to set your desired shade limits.
Top Limit can be set by moving the shade to the desired top position using the Up/Down
Buttons, then hold the Up Button and the Stop Button for 2-3 seconds. The shade will jog to
indicate that the top limit is set.
Bottom Limit can be set by moving the shade to the desired bottom position using the
Up/Down Buttons, then hold the Down Button and the Stop Button for 2-3 seconds. The
shade will jog to indicate that the bottom limit is set.
Adjusting Top Limit
If your limits are already set and you would like to adjust your top limit, follow the quick and
easy steps below.
1. Move your shade to the top limit using the Up/Down Buttons.
2. Hold the Up Button and the Stop Button for 5 seconds until the shade jogs twice
3. Jog the shade with your Up/Down Buttons to your new desired top limit.
4. Hold the Up Button and the Stop Button for 2-3 seconds. The shade will jog to indicate
Adjusting Bottom Limit
If your limits are already set and you would like to adjust your bottom limit, follow the quick and easy steps below.
1. Move your shade to the bottom limit using the Up/Down Buttons.
2. Hold the Down Button and the Stop Button for 5 seconds until the shade jogs twice
3. Jog the shade with your Up/Down Buttons to your new desired bottom limit.
4. Hold the Down Button and the Stop Button for 2-3 seconds. The shade will jog to indicate that
Setting Favorite Position
1. Move your shade to desired favorite position with the Up/Down Buttons then press the (P) Button
2. After the shade responds, press the Stop Button
3. After the shade has responded again, press the Stop Button and the shade will jog twice.
You can now navigate to the favorite position by using the Favorite Button:
You can remove it by moving the shade to the favorite position, then doing the exact same set
of commands.
Slowing Motors Down
Press the (P) Button on the back of the remote once, then the Down Button twice. You need to
Speeding Motors Up
Press the (P) Button on the back of the remote once, then the Up Button twice. You need to
wait for the motor to respond between button presses.
Position Percent Setting (Accurate Positioning)
Limits MUST be set before using this feature
1. Press the Stop Button three times
2. Use the (Left/Right) Buttons to increase or decrease percent
3. After 2 seconds, the shade will move to that limit
Advanced Options
1. Select Channel “01” using (Left/Right) Buttons
2. Press Favorite Button and Right Button for 3s - display will show:
3. Remote will go to channel 16 with the directional indicators on the side
4. Select the final channel you want (cannot be higher than 16 or lower than 1) using
(Left/Right) Buttons
5. Short press (click/tap and immediately release) the Stop Button, display will show:
Setting Number of Groups (Optional)
1. Select Channel “00” using (Left/Right) Buttons
2. Press Favorite Button and Right Button for 3s - display will show:
3. Remote will go to group 6 with the directional indicators on the side
4. Select the final group number you want (cannot be higher than 6)
5. Short press (click/tap and immediately release) the Stop Button, display will show:
Modifying (Adding + Deleting Channels from Groups)
1. Select Desired Group using (Left/Right) Buttons
2. Press Favorite Button and Right Button for 3s - display will show:
3. Remote will go to channel 1 with the group and directional indicators.
4. Navigate to desired channel to add or remove by using (Left/Right) Buttons
5. Short press Favorite Button to add to the group.
If the channel has already been added, it will flash on and off. Press the favorite button again to remove it from the group.
6. Once channels are added to the desired group, short press the Stop button. Display will show:
If you select Channel “00” as your final channel, you will have no groups on the remote. They can
Removing Groups
1. Hold the (P) Button on the back of the remote for 10 seconds. Your screen will display the icon below when locking function is activated:
Factory Reset
To remove all shade pairings and limits, hold the motor button until the shade jogs 4 times.
1. Place the magnetic remote mount on a wall where you’d like your remote to reside.
2. Using the two screws provided, screw the mount into the wall through the designated screw holes.
3. Make sure the mount is secure and place your remote on the magnetic mount.
Mounting Wall Remote
1. Remove magnetic mount from the back of the remote and place on the wall in a desired location where you’d like the wall remote to reside.
2. Using the two screws provided, screw the mount into the wall through the designated screw holes.
3. Make sure the mount is secure and place your remote on the magnetic mount.
Caution
1. The transmitter should not be exposed to moisture or impact.
2. During use, when the remote control distance is significantly shorter or less sensitive, please check to see if the batter needs replaced.
3. When the battery voltage is too low, the LCD screen will show a low battery indicator prompting to replace the battery.
4. Please properly dispose of the used batteries
Hold down the programming button on the motor until it jogs a total of three times. This will reverse the direction.
The limits on the shade have not been set. You will need to follow the limit correction steps, but do NOT follow the first step for both limits.
Yes! This can be done by holding the motor button for 4 full cycles. This takes normally about 15 seconds. Once this is done, you will need to re-pair a remote and re-set the limits. Follow the limit correction steps without the first step!
Ensure you're waiting for the motor to finish beeping before you pair it. If you're still having issues, hold the STOP button on the remote for 30 seconds twice. If it shows L both times, proceed with these instructions:
Yes! However, it is important you pair them individually first. If you pair them all to the same channel initially and you need to correct limits, you will be controlling every shade on that channel at a time.
Your remote is more than likely locked:
If you are using a Single Channel remote, the LED should flash while you are setting limits. If it is not, your remote is locked. This can be fixed by holding the STOP button for 30 seconds - the LED should turn on briefly once the remote is unlocked/locked.
If you are using a Multi-Channel Remote, the display should show two wifi-Esque symbols to the right of the channel while you're setting limits. If not, your remote is locked. This can be fixed by holding the STOP button for 30 seconds - the remote will then indicate which mode it is in by displaying a "U" for UNLOCKED or an "L" for LOCKED.
Please proceed to the Shimming and You section. It will walk you through the process of how to adjust for tracking!